- #Voodoo 1 8mb macmagic 3dfx mod#
- #Voodoo 1 8mb macmagic 3dfx drivers#
- #Voodoo 1 8mb macmagic 3dfx mods#
#Voodoo 1 8mb macmagic 3dfx drivers#
Also I've read that the drivers can make use of the full 8mb so there will be no problems. I have a Canopus 6mb version that is really about 15-20 percent faster in 3dmark99 on a p1 233mmx vs a normal 4mb card so more ram can have an impact on performance, don't know about glide. I have several ''good looking'' v1 cards that work great so making 1 a bit uglier is okay for me, if I can I will use a card that artifacts right now so with a bit of luck I'll make good use of a card that was defective before!
#Voodoo 1 8mb macmagic 3dfx mods#
Just want to create the fastest voodoo1 I can produce with these mods as I really love the voodoo1 but finding a real 8mb version is pretty hard and expensive. The card will get ''ugly'' but I don't care. 3DFX VooDoo 1 4 MB (Gainward) 3DFX VooDoo 1 4 MB (InnoVision) 3DFX VooDoo 1 6 MB (MiroMedia) 3DFX VooDoo Rush 6 MB (Atrend) 3DFX VooDoo Rush 4 MB (Britek ViewTOP) 3DFX Voodoo Rush 6 MB (Apollo Joytech BOX) 3DFX VooDoo II 8 MB (Diamond) 3DFX VooDoo II 12 MB (Diamond) 3DFX VooDoo II 12 MB (Creative) 3DFX VooDoo II 12 MB (Gainward 100 MHz) 3DFX. Diamond Multimedia 3dfx Voodoo 2 8MB PCI Graphics accelerator. 1.06 at the best online prices at eBay Free shipping for many products Skip to main content. Thread starter keke Start date 1 keke Weaksauce. Find many great new & used options and get the best deals for 3DFX VOOAGP - 64MB Hyundai Ram - VGA - REV. I guess I have to go trough some documents to find out the pinouts for the ram and the 3dfx chips. Obsidian3D 3Dfx 50-4400 Rev B 8MB 3D Voodoo 1 + AMETHYST Daughter Card. Thanks I have seen these before but was really hoping for some sharp pics to see what pin is what. I only had at hand 100 ohm ones and used those and had no problem. For the chips piggybacked to those that are wired 125, connect pin 14 to pin 180 on the FBI. For the chips piggybacked to those that are wired 124, connect pin 14 to pin 199 on the FBI. 4 - 8 MB EDO RAM (2-4MB Frame Buffer, 2-4MB for TMU) Scalable architecture (profi segment) API, rendering: MS Direct 3D. You should have 2 of them linked to pin 124 of the FBI and the other 2 to pin 125. 24bit internal, 16bit dithered RGB Frame Buffer. Todays Posts Member List Calendar Donations Forum Want to Sell Hardware for sale Other New Registrations are currently disabled Sorry for this inconvenience.
Check with a multimeter where pin 14 on the original modules connect. Stack RAM chips ontop those 4 allocated to the FBI and solder each pin to the same below except pin 14.
Connect pin 14 on all 4 piggybacked modules to pin 130 of the TMU through a 22-47 ohm resistor. Stack RAM chips ontop those 4 allocated to the TMU and solder each pin to the same below except pin 14. Stack RAM chips ontop those 4 allocated to the TMU and solder each pin to the same below ex But his instructions should be good enough to add the extra RAM.
#Voodoo 1 8mb macmagic 3dfx mod#
I only have really bad photos that were provided by the author of this mod at Falconfly forum long time ago.
0 kommentar(er)
